Blog

Dec 09, 2023

Waste heat recovery units in the coal industry

Save to read list Published by Angharad Lock, Digital Assistant Editor World Coal, Thursday, 20 April 2017 14:46

Although they have been around for a long time, there is still misunderstanding around how waste heat recovery units can be used by the coal industry says Matthew Crewe from waste heat recovery solution specialists Green's. Even where supplies of coal are abundant, there is still a need to use it efficiently and to look at ways that energy produced as a result of its burning may be reused.

A waste heat recovery unit/heat exchanger recovers heat from hot streams, gasses that still have relatively high energy content in them. This would otherwise go unused into the atmosphere. The most common examples of these units are those taking the exit gases from boilers in the world's largest coal fired power stations.

The diagram show waste heat recovery using an economiser application, technology that was first developed by Green's founder back in the mid 1800s and has been developed considerably over the years.

Waste heat found in exhaust gas is extracted by the following equipment:

Obviously waste heat recovery comes with a capital cost for the design and manufacture of the system and the various solutions on the market need to be assessed in terms of their track record in meeting the specific needs of the coal industry. However, taking steps to determine whether a valuable heat source can be used rather than wasted is always worth the effort.

Most power stations burn many millions of tons of coal per year which can come in various forms and quality from very dirty coal in some regions to very pure coal in others. This dictates the heat produced and the plant and equipment needed to optimise use of the heat.

Once at the power station the coal is stored, then pulverised before being burned in the power station. The heat taken from this process then heats the boilers. As the boiler is heated the gasses need to exit of course. These gasses are usually still at significantly high temperatures, so capturing the heat from the boiler using economisers and reusing it to heat water in tubes means it can be utilised to preheat the feed water and increase efficiency overall.

Throughout this stage, the coal (depending on its quality/consistency) creates ash when it is burned. The type and consistency will depend on the quality of the coal. Combined with the intense heat this ash is often highly abrasive which means that the boilers, burners and ancillary equipment at the power station need to be particularly robust if they are to perform effectively and provide acceptable system life.

To gain the maximum benefit from the waste heat from the boiler there are essential criteria that need to be considered with regard to selecting the most effective economisers. These include ensuring that the correct and durable materials are used and that the design and positioning of the economiser itself are appropriate to achieve the required heat transfer.

One design solution, to optimise heat transfer is by using extended surface tubing. This is done by adding fins to the tubing as shown below in a similar way to a radiator. This ensures the heat transfer into the tube is maximised by using the fin to conduct heat into the tube.

The use of H finned tube technology, rather than plain tubes, is particularly suited to power stations which want to maximise waste heat recovery as efficiency can be significantly increased within the space available. This usually results in reducing the number of tubes, the economiser size and in turn the heat of the exhaust gasses needed and input fuel used.

H fin applications – based on their design are well suited to both light and heavy fouling, high ash content, applications with most modern stations using this application. Indeed our proprietary steel H finned tubes are used in more than 70% of UK coal fired power stations and many more around the world.

Recent coal fired power station case studies

Projects include:

Green's has been designing and manufacturing waste heat recovery systems and economisers since 1845. Our heritage is within the coal market and our expertise is still very much in demand where this resource is plentiful alongside increasing interest from the biomass sector.

Gaining the greatest efficiency from the coal reserves that are used is clearly still a very important factor in the industry, the use of waste heat recovery further aids this through the use of economiser equipment.

Submitted by waste heat recovery solution specialists, Green's.

Read the article online at: https://www.worldcoal.com/coal/20042017/waste-heat-recovery-units-in-the-coal-industry/

Two large carbon capture projects recently held a groundbreaking ceremony at the Wyoming Integrated Test Center (ITC).

Embed article link: (copy the HTML code below):

This article has been tagged under the following:

US coal news